Stainless Steel 3-Piece 60 Series Ball Valve, Reinforced PTFE Seats, 1/4 in. FNPT

1/8 至 2 in. 和 6 至 25 mm 口径, 不锈钢、碳钢和黄铜和特种合金材料, 通-断 (2 通) 阀和切换 (3 通) 阀, 补偿阀座设计, 活动负载的、两件式阀杆填料

Features: Operating temperatures up to 400°F (204°C); Working pressures up to 2200 psig (151 bar); Stainless steel or carbon steel construction

Latch lock handle assembly to 4-bolt and 8-bolt 60 series ball valves

Features: Swagelok® electric actuators can be used to control the position of many Swagelok ball valves; alternating- and direct-current models are available. An electrical signal is used to change valve position from remote locations. Integral limit switches provide an output signal of the valve position, even between positions.

Features: Rack and pinion pneumatic actuators, solenoid valves, and limit switches; ISO 5211-compliant pneumatic actuators, solenoid valves, limit switches, and position sensors; Complete actuated assemblies and kits for field assembly available

本技术报告是为了能安全地处理氧气而必须提出的独特考虑的概述。 技术数据

只适用于3通：检验执行轴上的涂料点位置; 它应该朝向 线管连接; 从执行器上去除四个安装支架螺丝; 将安装支架置于执行器上，转动它直到墙面安装翼片位 置远离执行器的前部; 重装四个安装支架螺丝并拧紧到 20到30 in.·lb (2.3 到 3.4 N·m).

松开并去除8根阀体螺栓; 从法兰中移去中心阀体; 去除并丢弃两套法兰密封和阀座组件; 去除支撑环并置于一边以备后用。

Valves may be welded into system WITHOUT disassembly; Valve disassembly will damage flange seals and require their replacement; Additional seal kits are available for routine maintenance.

松开和去除8个阀体螺栓; 去除法兰端之间的中心阀体; 取下并丢弃两套法兰 密封，背阀座和阀座; 旋转球至关闭位置。取出并 丢弃球。

40G, 40, 60, 83, H83 和 SK 系列球阀AFS 球阀 ■ 计算阀门操作扭矩 ■ 选择执行机构及相关部件 ■ 选择安装支架成套件

Electric Actuator Installation

打开阀门; 将阀门摆出侧的“C”位置的阀体紧固件拆除。（参见里面的示意图。）; 拧松其余的阀体紧固件; 将中心阀体摆出并拆除O型圈密封、阀座、（以及60M系列上的背阀座）和阀座支撑环. 不要 清除这些零部件上的润滑剂. 放在一边以备复装。≠

This document specifies guidelines used by Swagelok® Company and its suppliers to ensure compliance with product cleanliness requirements as stated in ASTM G93 Level C. Application of the document is limited to wetted system components. This document must be used in conjunction with product catalogs, technical bulletins, and reports.

杆式和椭圆形手柄 ; 杆式和椭圆形手柄的锁定支架 ; 椭圆形闩锁手柄

工具清单; 六角扳手: 1/8 in., 9/64 in., 5/32 in., 3/16 in., 5/16 in.; 开口延伸工具: 5/16 in., 3/8 in., 7/16 in., 9/16 in., 5/8 in., 3/4 in., 11/16 in., 15/16 in.; 扭矩扳手，可以达到 700 in.·lbs (79.1 N·m, 806 cm·kg)

Using a box wrench, remove the stem nut, stem springs, stop plate and lever handle; 63 series only: Place extended handle positioner plate on stem.

To ensure proper valve function, valve must be installed with flow in the direction indicated by the arrow on the valve body.

Caution: Pneumatic actuator operation is sensitive to valve packing nut adjustment.

Abstract of Cleaning Procedure For Chlorine Series Valves.

Kit contents: Standard Fastener (bolt or stud 3), Instruction sheet, Black Fastener (bolt or stud), Stem nuts (2), Body nuts (8), Lubricants (1), Material Safety Data Sheets (1)

НСТРУКЦИИ ПО ТЕХНИЧЕСКОМУ ОБСЛУЖИВАНИЮ ВСТАВОК ДЛЯ УМЕНЬШЕНИЯ МЕРТВОЙ ЗОНЫ СЕРИЙ «60» И «60X»

Warning: Before servicing any installed valve, you must depressurize the system cycle valve Mounting Namur Style Bracket to 2-way 60 series ball valve.

60 Series Ball Valves, 4-Bolt, No Lube Instructions

В настоящем документе изложены инструкции, используемые компанией Swagelok для производства продуктов из нержавеющей стали, предназначенных для фотоэлектрических систем.

Данный сменный комплект шарика должен использоваться с соответствующим ремонтным комплектом уплотнителей для клапанов серии 60

Данный сменный комплект штока должен использоваться с соответствующим ремонтным комплектом уплотнителей для серии 60.

Инструкции по техобслуживанию шаровых кранов серий 60 и 60X с 4 болтами

60 Series Flange Seal Installation