Stainless Steel 3-Piece 60 Series Steam Service Ball Valve, PEEK Seats, 1 in. Swagelok Tube Fitting

1/8 至 2 in. 和 6 至 25 mm 口径, 不锈钢、碳钢和黄铜和特种合金材料, 通-断 (2 通) 阀和切换 (3 通) 阀, 补偿阀座设计, 活动负载的、两件式阀杆填料

杆式和椭圆形手柄 ; 杆式和椭圆形手柄的锁定支架 ; 椭圆形闩锁手柄

Features: Swagelok® electric actuators can be used to control the position of many Swagelok ball valves; alternating- and direct-current models are available. An electrical signal is used to change valve position from remote locations. Integral limit switches provide an output signal of the valve position, even between positions.

40G, 40, 60, 83, H83 和 SK 系列球阀AFS 球阀 ■ 计算阀门操作扭矩 ■ 选择执行机构及相关部件 ■ 选择安装支架成套件

特点：齿条齿轮气动执行机构、电磁阀和限位开关；符合 ISO 5211 标准的气动执行机构、电磁阀、限位开关和位置传感器；可用于现场装配的完整执行组件和成套件

Features: Operating temperatures up to 400°F (204°C); Working pressures up to 2200 psig (151 bar); Stainless steel or carbon steel construction

本技术报告是为了能安全地处理氧气而必须提出的独特考虑的概述。 技术数据

This document specifies guidelines used by Swagelok® Company and its suppliers to ensure compliance with product cleanliness requirements as stated in ASTM G93 Level C. Application of the document is limited to wetted system components. This document must be used in conjunction with product catalogs, technical bulletins, and reports.

此文件对世伟洛克公司生产用于光伏行业的不锈钢产品进行了规定。此文件必须与产品目录、技术公告及报告一起使用，这样产品信 息才完整。此文件的应用仅限于与介质接触的系统部件。

Pages 1-3. Features: installation in high-pressure applications and high safety-factor systems.

这个阀杆替换套件必须与适当的60系列密封维修套件一 起使用; 按密封维修套件说明去除使用过的阀杆，并用这 个套件中的阀杆代替。

这个阀球替换套件必须与适当的60系列密封维修套件一 起使用; 按密封维修套件说明去除使用过的球，并用这 个套件中的球代替。

工具清单; 六角扳手: 1/8 in., 9/64 in., 5/32 in., 3/16 in., 5/16 in.; 开口延伸工具: 5/16 in., 3/8 in., 7/16 in., 9/16 in., 5/8 in., 3/4 in., 11/16 in., 15/16 in.; 扭矩扳手，可以达到 700 in.·lbs (79.1 N·m, 806 cm·kg)

成套件包括： 标准紧固件 指示表（1） （螺栓或者柱头螺栓）（3） 黑色紧固件 阀杆螺母（2） （螺栓或者柱头螺栓）（1） 阀体螺母（8） 润滑剂(1) 材料安全数据表(1)

Latch lock handle assembly to 4-bolt and 8-bolt 60 series ball valves

Warning: Before servicing any installed valve, you must depressurize the system cycle valve Mounting Namur Style Bracket to 2-way 60 series ball valve.

To ensure proper valve function, valve must be installed with flow in the direction indicated by the arrow on the valve body.

Disassemble the cover screws, set them aside, and remove cover; Install wiring as indicated by wiring schematic.

松开并去除8根阀体螺栓; 从法兰中移去中心阀体; 去除并丢弃两套法兰密封和阀座组件; 去除支撑环并置于一边以备后用。

Valves may be welded into system WITHOUT disassembly; Valve disassembly will damage flange seals and require their replacement; Additional seal kits are available for routine maintenance.