Features: 1/8 to 2 in. and 6 to 25 mm sizes; Stainless steel, carbon steel, brass, and special alloy materials; On-off (2-way) and switching (3-way) valves; Compensating seat design; Live-loaded, two-piece stem packing

Features: Operating temperatures up to 400°F (204°C); Working pressures up to 2200 psig (151 bar); Stainless steel or carbon steel construction

Latch lock handle assembly to 4-bolt and 8-bolt 60 series ball valves

Features: Swagelok® electric actuators can be used to control the position of many Swagelok ball valves; alternating- and direct-current models are available. An electrical signal is used to change valve position from remote locations. Integral limit switches provide an output signal of the valve position, even between positions.

Features: Rack and pinion pneumatic actuators, solenoid valves, and limit switches; ISO 5211-compliant pneumatic actuators, solenoid valves, limit switches, and position sensors; Complete actuated assemblies and kits for field assembly available

Scope: This technical report is an overview of the unique concerns that must be addressed in order to handle oxygen safely. It is based on information found in the many source documents available from the publishers listed and is provided as a service to our customers.

Mounting Bracket Kit Contents; Actuator Kit Contents; Tools Required; Actuator Preparation; Valve Preparation; Mounting Instructions.

S60P steam series ball valve maintenance instructions

Valves may be welded into system WITHOUT disassembly; Valve disassembly will damage flange seals and require their replacement; Additional seal kits are available for routine maintenance.

松开和去除8个阀体螺栓; 去除法兰端之间的中心阀体; 取下并丢弃两套法兰 密封，背阀座和阀座; 旋转球至关闭位置。取出并 丢弃球。

40G, 40, 60, 83, H83 和 SK 系列球阀AFS 球阀 ■ 计算阀门操作扭矩 ■ 选择执行机构及相关部件 ■ 选择安装支架成套件

Disassemble the cover screws, set them aside, and remove cover; Install wiring as indicated by wiring schematic.

打开阀门; 将阀门摆出侧的“C”位置的阀体紧固件拆除。（参见里面的示意图。）; 拧松其余的阀体紧固件; 将中心阀体摆出并拆除O型圈密封、阀座、（以及60M系列上的背阀座）和阀座支撑环. 不要 清除这些零部件上的润滑剂. 放在一边以备复装。≠

This document specifies guidelines used by Swagelok® Company and its suppliers to ensure compliance with product cleanliness requirements as stated in ASTM G93 Level C. Application of the document is limited to wetted system components. This document must be used in conjunction with product catalogs, technical bulletins, and reports.

杆式和椭圆形手柄 ; 杆式和椭圆形手柄的锁定支架 ; 椭圆形闩锁手柄

工具清单; 六角扳手: 1/8 in., 9/64 in., 5/32 in., 3/16 in., 5/16 in.; 开口延伸工具: 5/16 in., 3/8 in., 7/16 in., 9/16 in., 5/8 in., 3/4 in., 11/16 in., 15/16 in.; 扭矩扳手，可以达到 700 in.·lbs (79.1 N·m, 806 cm·kg)

Using a box wrench, remove the stem nut, stem springs, stop plate and lever handle; 63 series only: Place extended handle positioner plate on stem.

To ensure proper valve function, valve must be installed with flow in the direction indicated by the arrow on the valve body.

Caution: Pneumatic actuator operation is sensitive to valve packing nut adjustment.

Abstract of Cleaning Procedure For Chlorine Series Valves.

成套件包括： 标准紧固件 指示表（1） （螺栓或者柱头螺栓）（3） 黑色紧固件 阀杆螺母（2） （螺栓或者柱头螺栓）（1） 阀体螺母（8） 润滑剂(1) 材料安全数据表(1)

Warning: Before servicing any installed valve, you must depressurize the system cycle valve Mounting Namur Style Bracket to 2-way 60 series ball valve.

使阀门处于开位置。拆卸前记住手柄的位置，因为重新组装时手柄必须处于相同的位置以指示合适 的阀门流向; 使用扳手，去除阀杆螺母，阀杆弹簧，止动板，手柄和接地弹簧。将阀杆弹簧之外的所有零件放在一 边备用。记住手柄的位置，因为手柄必须被重新装到相同的位置。注：62系列不使用上部阀杆弹簧。

此文件对世伟洛克公司生产用于光伏行业的不锈钢产品进行了规定。此文件必须与产品目录、技术公告及报告一起使用，这样产品信 息才完整。此文件的应用仅限于与介质接触的系统部件。

这个阀球替换套件必须与适当的60系列密封维修套件一 起使用; 按密封维修套件说明去除使用过的球，并用这 个套件中的球代替。

这个阀杆替换套件必须与适当的60系列密封维修套件一 起使用; 按密封维修套件说明去除使用过的阀杆，并用这 个套件中的阀杆代替。

60和60X系列4螺栓球阀维护说明

60 Series Flange Seal Installation